24V Low Voltage Power Switch Latch WR-51
This is a low voltage switch latch. When the common output is momentarily connected to the “On” input, the output will supply 24V DC on the Relay Output. When the common is momentarily connected to the “Off” input, the Relay Output will no longer supply any voltage. There is a variant of this with a reversible input.
Amplifier Power Sequencer WTC-52
This is a low voltage power on sequencer. When 12V is supplied to the input, each of the 4 outputs is time delayed on so that total inrush current of each device it controls does not exceed the AC circuit limit.
Piston Lamp Regulator WTC-70
This is a voltage regulator specifically designed for incandescent piston buttons. 12V DC rectifier voltage can be connected and an output between an adjustable 4.5 to 4.8 volts will be supplied on the output terminals.
High Current Lamp Regulator WTC-71
This is a voltage regulator specifically designed for incandescent bulbs. 14-20V DC rectifier voltage can be connected and an output of an adjustable voltage between 6-12V will be supplied to the output terminals. The maximum current is 6A.
FET Battery Switch WTC-53
This is a switch that can connect a very high current supply, like a battery that should normally be disconnected to drive coil magnets. The switch on time is around 120ns and is sufficiently fast to keep supplies from folding. The current capability can be configured up to 500 A.
Smart Power Distribution WTC-92
This is a power distribution board for use with Walker Smart controls. This board takes care of fusing all of the power links and distributing the Data to each Smart Device group. The fuses are automatically resettable and there is a diagnostic LED for each one of the 6 outputs, alerting to the fuse being open.
Magnetic Manual Keying
A very reliable and practical way to add velocity keying to any organ keyboard. The kit provides a keying strip with magnetic sensors and the magnets to mount on each key. Standard length 61 notes - can be special ordered to create any keyboard length from 21 notes up to 88 notes.
Magnetic Pedal Keying
Everything needed to install magnetic keying contacts on a pedal board. The pedal board contacts use magnets to sense when the pedal is pressed down. The depth can be set easily upon installation by sliding the circuit board up or down and watching the LED indicator on each sensor board. This kit comes with 32 pedal board sensors and 32 magnet assembles for mounting to the pedals.
LED pedal board light
LED light strip pedal board light, which produces evenly distributed lighting along the entire pedal board. The wooden strip is designed to mount on the bottom of the key desk, runs on 12V DC, and is dimmable with a PWM output.
Expression/Crescendo Shoe
An extremely consistent and reliable expression shoe, hand-built in the AEolian-Skinner® style. Providing incredibly low static friction with enough dynamic friction for accurate movement, the shoe offers consistent voltage outputs, requiring no adjustment or calibration once set up.
The shoe is available in:
- Pedestal or rail mount
- Polished chrome or black, powder-coated finish
- Rimmed with rubber tread or rimless for wood cap
- Analog (0-5 volts), discrete, or no electronic output
- Sostenuto or Sustain switch
Thumb Piston
A very reliable hall-effect (contactless) thumb piston with a concave surface and curved edge in the AEolian-Skinner® style. Available in white, red, black, or yellow, with a standard black or optional green surround. The piston can be configured for either positive or negative switch output and positive or negative light input. The LED back light mimics the warm color of an incandescent bulb. Custom engraving is available for all piston buttons.
Console Controller WTC-303
The most highly integrated console controller in the industry. It provides direct wiring for WTC’s proven magnetic keying system, Smart Controls or Standard Data Chain, MIDI input/output, PAL audio input/output, USB flash memory, user interface display and expression/crescendo analog inputs. Everything is contained in one small 7.25” x 7.25” board
Headphone Interface WTC-290
Headphone interface for use with the WTC-303 Console Controller. Includes a headphone jack with insertion detection and a volume knob.
User Interface Screen
A small black and white screen which displays information and interfaces with the WTC Console Controller. This screen is required to use the Console Controller.